6.25 USD
We are happy to bring you this wonderful banner cutter that I worked on with my friend, Callye, based on her beautiful banner design that she kindly offered us to turn into a cutter. There are actually four variations of her beautiful design - this being Banner 1, a longer banner with two variations with one being longer than the other. The other is Banner 2, which is under another listing and is a taller version of this design to allow for more writing space. You can find the Banner 2 Cutter at https://www.etsy.com/listing/511014679
Cutter prices are determined by print time and the amount of PLA used. Cutters with intricate shapes and curves or larger sizes take longer to print and are priced accordingly. This is one such cutter due to the curves.
Please note the graphic shown in the photo under the cutter photo to show how the measurements are done to avoid any confusion when ordering as this cutter is measured at the angle/positioning as the cutter was designed to be used rather than turned completely horizontal. This is because cookie decorators might be using the measurements to fit in a box, etc. at the angle the cutter is shown. So the measurements are for the tilted angle of this cutter. I state this as I don't want people to think that the cutter is larger than it actually is, so please note the tilted aspect when ordering and again, please see the graphic under the cutter photo above. Please choose from above under "Size" for any of the following:
BANNER 1A:
Banner 1A1:
Measurement 1 (shown in blue): 3 1/2" (so 3 1/2" wide when turned to that angle shown)
Measurement 2 (shown in green): 1 5/8" (so it is 1 5/8"high, but please note the angle that the cutter is turned to as that is important)
Measurement 3 (shown in red): approximately 7/8" x 2"(this is the maximum interior space, but one would not pipe lettering in general to the edge, but that is the approximate space inside)
Banner 1A2:
Measurement 1 (shown in blue): 4" (so 4" wide when turned to that angle shown)
Measurement 2 (shown in green): 1 7/8" (so it is 1 7/8" high, but please note the angle that the cutter is turned to as that is important)
Measurement 3 (shown in red): approximately just under 1 1/8" x 2 1/4" (this is the maximum interior space, but one would not pipe lettering in general to the edge, but that is the approximate space inside)
BANNER 1B (a bit longer/wider than 1A):
Banner 1B1:
Measurement 1 (shown in blue): 4" (so 4" wide when turned to that angle shown)
Measurement 2 (shown in green): 1 1/2" (so it is 1 1/2" high, but please note the angle that the cutter is turned to as that is important)
Measurement 3 (shown in red): approximately just under 7/8" x 2 5/8 (this is the maximum interior space, but one would not pipe lettering in general to the edge, but that is the approximate space inside)
Banner 1B2:
Measurement 1 (shown in blue): 4 1/2" (so 4 1/2" wide when turned to that angle shown)
Measurement 2 (shown in green): 1 5/8" (so it is 1 5/8" high, but please note the angle that the cutter is turned to as that is important)
Measurement 3 (shown in red): approximately just under 1" x 3" (this is the maximum interior space, but one would not pipe lettering in general to the edge, but that is the approximate space inside)
I will also be including Guideline Sketches later should anyone wish to use them as a guide. You will find them under the photos of the cutter. To save it, click on the photo, right click to either "Save Image" or "Copy Image". From there paste into Word or whichever program you like. You can then resize it from there as needed and place it on a KopyKake or alongside your cookie as you pipe.
.
Whisked Away Cutters are finely crafted cutters for cookies and fondant, designed by a cookie decorator for cookie decorators. Crafted with rounded corners on the handle for comfort, a reinforced area near the base of the handle and strong walls going down to a fine tapered edge for a precise, clean cut. Please see the cutter side view example in the close up photo of The Vicki plaque cutter shown above in the thumbnail photos.
** Food safe PLA cutters are HAND WASH ONLY, not dishwasher safe, cannot be used to cut hot and should not be left to soak in hot water. This is an aspect of all food safe PLA cutters. Care must be given to the specialized tapered cutting edge when storing as it can get nicked or damaged if hit with another cutter or sharp object. Proper care will ensure years of use from your Whisked Away Cutters.
Maryann, The Cookie Artisan, recently had this to say, "I love how your cutters feel in my hands and how comfortable the edges feel as I cut cookies! Used my first cutter to cut 350 cookies and the edges on the last cookie looked as great as the first cookie!"
Current shipping time is shown on our home page beneath the banner at https://www.etsy.com/shop/whiskedawaycutters Shipping for our shop is done via USPS First Class Mail, which is listed as 3 - 5 days on average. Priority Mail is listed as 2 - 3 days on average and is available for purchase as a separate item. Again, shipping times are not guaranteed. Please bear in mind the normal order processing time that is shown. We will make all efforts to expedite your order when Priority Mail is selected, but it will be a matter of the number of orders already placed. Please see "Shipping & Policies" for more shop information.